Annotation of OpenXM_contrib/gnuplot/term/epson.trm, Revision 1.1.1.2
1.1 maekawa 1: /*
1.1.1.2 ! maekawa 2: * $Id: epson.trm,v 1.8 1998/12/14 18:38:55 lhecking Exp $
1.1 maekawa 3: *
4: */
5:
6: /* GNUPLOT - epson.trm */
7:
8: /*[
9: * Copyright 1990 - 1993, 1998
10: *
11: * Permission to use, copy, and distribute this software and its
12: * documentation for any purpose with or without fee is hereby granted,
13: * provided that the above copyright notice appear in all copies and
14: * that both that copyright notice and this permission notice appear
15: * in supporting documentation.
16: *
17: * Permission to modify the software is granted, but not the right to
18: * distribute the complete modified source code. Modifications are to
19: * be distributed as patches to the released version. Permission to
20: * distribute binaries produced by compiling modified sources is granted,
21: * provided you
22: * 1. distribute the corresponding source modifications from the
23: * released version in the form of a patch file along with the binaries,
24: * 2. add special version identification to distinguish your version
25: * in addition to the base release version number,
26: * 3. provide your name and address as the primary contact for the
27: * support of your modified version, and
28: * 4. retain our contact information in regard to use of the base
29: * software.
30: * Permission to distribute the released version of the source code along
31: * with corresponding source modifications in the form of a patch file is
32: * granted with same provisions 2 through 4 for binary distributions.
33: *
34: * This software is provided "as is" without express or implied warranty
35: * to the extent permitted by applicable law.
36: ]*/
37:
38: /*
39: * This file is included by ../term.c.
40: *
41: * This terminal driver supports:
42: * epson_lx800, nec_cp6, starc,
43: * epson_60dpi, tandy_60dpi
44: * epson_180dpi
45: *
46: * AUTHORS
47: * Russell Lang
48: * William Wilson
49: *
50: * send your comments or suggestions to (info-gnuplot@dartmouth.edu).
51: *
52: */
53:
54: /*
55: * adapted to the new terminal layout by Stefan Bodewig (1995)
56: */
57:
58: #include "driver.h"
59:
60: #ifdef TERM_REGISTER
61: #ifdef EPS180
62: register_term(epson_180dpi)
63: #endif /* EPS180 */
64: #ifdef EPS60
65: register_term(epson_60dpi)
66: #endif /* EPS60 */
67: #ifdef EPSONP
68: register_term(epson_lx800)
69: #endif /* EPSONP */
70: #ifdef NEC
71: register_term(nec_cp6)
72: #endif /* NEC */
73: #ifdef OKIDATA
74: register_term(okidata)
75: #endif /* OKIDATA */
76: #ifdef STARC
77: register_term(starc)
78: #endif /* STARC */
79: #ifdef TAMDY60
80: register_term(tandy_60dpi)
81: #endif /* TANDY60 */
82: #endif /* TERM_REGISTER */
83:
84: #ifdef TERM_PROTO
85:
86: #if defined(EPS180) || defined(EPS60) || defined(EPSONP) || defined(TANDY60) || defined(OKIDATA)
87: TERM_PUBLIC void EPSONinit __PROTO((void));
88: TERM_PUBLIC void EPSONreset __PROTO((void));
89: #define EPSONlinetype b_setlinetype
90: #define EPSONmove b_move
91: #define EPSONvector b_vector
92: #define EPSONput_text b_put_text
93: #define EPSON_text_angle b_text_angle
94:
95: #if defined(EPS60) || defined(EPSONP) || defined(TANDY60) || defined(OKIDATA)
96: #define EPSONVCHAR FNT5X9_VCHAR
97: #define EPSONHCHAR FNT5X9_HCHAR
98: #define EPSONVTIC 6
99: #define EPSONHTIC 6
100:
101: #ifdef EPSONP
102: #define EPSONXMAX 512
103: #define EPSONYMAX 384
104: TERM_PUBLIC void EPSONgraphics __PROTO((void));
105: TERM_PUBLIC void EPSONtext __PROTO((void));
106: #endif /* EPSONP */
107: #endif /* four drivers */
108: #endif /* all five */
109:
110: #ifdef EPS180
111: TERM_PUBLIC void EPS180graphics __PROTO((void));
112: TERM_PUBLIC void EPS180text __PROTO((void));
113: #define EPSON180VCHAR FNT13X25_VCHAR
114: #define EPSON180HCHAR FNT13X25_HCHAR
115: #define EPSON180VTIC 18
116: #define EPSON180HTIC 18
117: /* make the total dimensions 8 inches by 6 inches */
118: #define EPS180XMAX 1260
119: #define EPS180YMAX 1080
120: #endif /* EPS180 */
121:
122: #if defined(EPS60) || defined(TANDY60) || defined(OKIDATA)
123: /* make the total dimensions 8 inches by 5 inches */
124: #define EPS60XMAX 480
125: #define EPS60YMAX 360
126: TERM_PUBLIC void EPS60graphics __PROTO((void));
127: #ifdef TANDY60
128: TERM_PUBLIC void TANDY60text __PROTO((void));
129: #endif /* TANDY60 */
130: #ifdef OKIDATA
131: TERM_PUBLIC void OKIDATAtext __PROTO((void));
132: #endif /* OKIDATA */
133: #ifdef EPS60
134: TERM_PUBLIC void EPS60text __PROTO((void));
135: #endif /* EPS60 */
136: #endif /* all three */
137:
138: #ifdef NEC
139: TERM_PUBLIC void NECoptions __PROTO((void));
140: TERM_PUBLIC void NECinit __PROTO((void));
141: TERM_PUBLIC void NECgraphics __PROTO((void));
142: TERM_PUBLIC void NECtext __PROTO((void));
143: TERM_PUBLIC void NEClinetype __PROTO((int linetype));
144: TERM_PUBLIC void NECreset __PROTO((void));
145: #define NECmove b_move
146: #define NECvector b_vector
147: #define NECput_text b_put_text
148: #define NEC_text_angle b_text_angle
149: #define NECXMAX 400
150: #define NECYMAX 320
151: #define NECVCHAR FNT5X9_VCHAR
152: #define NECHCHAR FNT5X9_HCHAR
153: #define NECVTIC 6
154: #define NECHTIC 6
155: #endif /* NEC */
156:
157: #ifdef STARC
158: TERM_PUBLIC void STARCinit __PROTO((void));
159: TERM_PUBLIC void STARCgraphics __PROTO((void));
160: TERM_PUBLIC void STARCtext __PROTO((void));
161: TERM_PUBLIC void STARClinetype __PROTO((int linetype));
162: TERM_PUBLIC void STARCreset __PROTO((void));
163: #define STARCmove b_move
164: #define STARCvector b_vector
165: #define STARCput_text b_put_text
166: #define STARC_text_angle b_text_angle
167: #define STARCXMAX 512
168: #define STARCYMAX 384
169: #define STARCVCHAR FNT5X9_VCHAR
170: #define STARCHCHAR FNT5X9_HCHAR
171: #define STARCVTIC 6
172: #define STARCHTIC 6
173: #endif /* STARC */
174:
175: #endif /* TERM_PROTO */
176:
177: #ifndef TERM_PROTO_ONLY
178: #ifdef TERM_BODY
179:
180:
181: #ifdef EPSONP
182:
183: /* The following epson lx800 driver uses generic bit mapped graphics
184: routines to build up a bit map in memory. */
185: /* by Russell Lang, rjl@monu1.cc.monash.edu.au */
186: /* On PC, print using 'copy file /b lpt1:', do NOT use 'print' */
187: /* EPSON_init changes gpoutfile to binary mode on PC's */
188:
189: void epson_dump __PROTO((void));
190:
191: #define EPSONXLAST (EPSONXMAX - 1)
192: #define EPSONYLAST (EPSONYMAX - 1)
193:
194: TERM_PUBLIC void EPSONinit()
195: {
196: }
197:
198: TERM_PUBLIC void EPSONgraphics()
199: {
200: b_charsize(FNT5X9);
201: b_makebitmap((unsigned int) (EPSONXMAX * xsize),
202: (unsigned int) (EPSONYMAX * ysize), 1);
203: }
204:
205:
206: TERM_PUBLIC void EPSONtext()
207: {
208: epson_dump();
209: b_freebitmap();
210: }
211:
212:
213: TERM_PUBLIC void EPSONreset()
214: {
215: #ifdef VMS
216: fflush_binary();
217: #endif
218: }
219:
220:
221: /* output file must be binary mode for epson_dump */
222: void epson_dump()
223: {
224: register unsigned int x;
225: int j;
226: for (j = (b_ysize / 8) - 1; j >= 0; j--) {
227: /* select plotter graphics mode (square pixels) */
228: fputs("\033J\030", gpoutfile); /* line feed 8/72" = 8 dots */
229: fputs("\r\033*\005", gpoutfile);
230: (void) fputc((char) (b_xsize % 256), gpoutfile);
231: (void) fputc((char) (b_xsize / 256), gpoutfile);
232: for (x = 0; x < b_xsize; x++) {
233: (void) fputc((char) (*((*b_p)[j] + x)), gpoutfile);
234: }
235: }
236: #ifdef PC
237: fputs("Print using: COPY /B\n", stderr);
238: #endif
239: }
240:
241: #endif /* EPSONP */
242:
243:
244: /* The following NEC CP6 Pinwriter driver uses generic bit mapped graphics
245: routines to build up a bit map in memory. */
246: /* by Russell Lang, rjl@monu1.cc.monash.edu.au */
247: /* On PC, print using 'copy file /b lpt1:', do NOT use 'print' */
248: /* NECinit changes gpoutfile to binary mode for PC's */
249:
250: /* Add a Monochrome NEC printer (for faster speed and line types) jdc */
251:
252: #ifdef NEC
253:
254: void nec_dump __PROTO((void));
255: void nec_draft_dump __PROTO((void));
256:
257: #define NECXLAST (NECXMAX - 1)
258: #define NECYLAST (NECYMAX - 1)
259:
260:
261: /* plane 0=black, 1=cyan(blue), 2=magenta(red), 3=yellow */
262: static unsigned int neccolor[] = { 1, 8, 4, 2, 10, 12, 6, 14 };
263: static unsigned int necpcolor[] = { 0, 2, 1, 4 };
264:
265: static int NECmode;
266:
267: TERM_PUBLIC void NECoptions()
268: {
269: if (END_OF_COMMAND) {
270: strcpy(term_options, "monochrome");
271: NECmode = 'm';
272: } else if (almost_equals(c_token, "m$onochrome")) {
273: c_token++;
274: strcpy(term_options, "monochrome");
275: NECmode = 'm';
276: } else if (almost_equals(c_token, "c$olor")
277: || almost_equals(c_token, "c$olour")) {
278: c_token++;
279: strcpy(term_options, "color");
280: NECmode = 'c';
281: } else if (almost_equals(c_token, "d$raft")) {
282: c_token++;
283: strcpy(term_options, "draft");
284: NECmode = 'd';
285: } else {
286: /* error, but since the terminal is already set, default to mono */
287: strcpy(term_options, "monochrome");
288: NECmode = 'm';
289: int_error("modes: color, monochrome, draft", c_token);
290: }
291: }
292:
293: TERM_PUBLIC void NECinit()
294: {
295: }
296:
297: TERM_PUBLIC void NECgraphics()
298: {
299: b_charsize(FNT5X9);
300: b_makebitmap((unsigned int) (NECXMAX * xsize),
301: (unsigned int) (NECYMAX * ysize), (NECmode == 'c' ? 4 : 1));
302: }
303:
304: TERM_PUBLIC void NECtext()
305: {
306: if (NECmode == 'd') {
307: nec_draft_dump();
308: } else {
309: nec_dump();
310: }
311: b_freebitmap();
312: }
313:
314: TERM_PUBLIC void NEClinetype(linetype)
315: int linetype;
316: {
317: if (NECmode == 'c') {
318: if (linetype >= 6)
319: linetype %= 6;
320: b_setvalue(neccolor[linetype + 2]);
321: } else {
322: b_setlinetype(linetype);
323: }
324: }
325:
326:
327:
328: TERM_PUBLIC void NECreset()
329: {
330: #ifdef VMS
331: fflush_binary();
332: #endif
333: }
334:
335:
336: /* output file must be binary mode for nec_dump */
337: void nec_dump()
338: {
339: unsigned int x;
340: unsigned int plane, offset;
341: int j;
342: unsigned int column8;
343: unsigned long column24;
344: char column3, column2, column1;
345: fputs("\033P\033l\005", gpoutfile); /* 10cpi, left margin 5 char */
346: for (j = (b_ysize / 8) - 1; j >= 0; j--) {
347: fputs("\033J\030", gpoutfile); /* 24/180" line feed */
348: for (plane = 0; plane < b_planes; plane++) {
349: offset = plane * b_psize;
350: if (b_planes > 1) {
351: /* select colour for plane */
352: fputs("\033r", gpoutfile);
353: (void) fputc((char) necpcolor[plane], gpoutfile);
354: }
355: /* select plotter graphics mode (square pixels) */
356: fputs("\r\033*\047", gpoutfile);
357: (void) fputc((char) ((b_xsize * 3) % 256), gpoutfile);
358: (void) fputc((char) ((b_xsize * 3) / 256), gpoutfile);
359: for (x = 0; x < b_xsize; x++) {
360: column8 = (unsigned int) (*((*b_p)[j + offset] + x));
361: column24 = 0;
362: if (column8 & 0x01)
363: column24 |= (long) 0x000007;
364: if (column8 & 0x02)
365: column24 |= (long) 0x000038;
366: if (column8 & 0x04)
367: column24 |= (long) 0x0001c0;
368: if (column8 & 0x08)
369: column24 |= (long) 0x000e00;
370: if (column8 & 0x10)
371: column24 |= (long) 0x007000;
372: if (column8 & 0x20)
373: column24 |= (long) 0x038000;
374: if (column8 & 0x40)
375: column24 |= (long) 0x1c0000;
376: if (column8 & 0x80)
377: column24 |= (long) 0xe00000;
378: column1 = (char) (column24 & (long) 0xff);
379: column2 = (char) ((column24 >> 8) & (long) 0xff);
380: column3 = (char) ((column24 >> 16) & (long) 0xff);
381: (void) fputc(column3, gpoutfile);
382: (void) fputc(column2, gpoutfile);
383: (void) fputc(column1, gpoutfile);
384: (void) fputc(column3, gpoutfile);
385: (void) fputc(column2, gpoutfile);
386: (void) fputc(column1, gpoutfile);
387: (void) fputc(column3, gpoutfile);
388: (void) fputc(column2, gpoutfile);
389: (void) fputc(column1, gpoutfile);
390: }
391: }
392: }
393: fputs("\r\033l", gpoutfile);
394: (void) fputc('\0', gpoutfile); /* set left margin to 0 */
395: if (b_planes > 1) {
396: fprintf(gpoutfile, "\033r");
397: (void) fputc('\0', gpoutfile); /* set color to black */
398: }
399: #ifdef PC
400: fputs("Print using: COPY /B\n", stderr);
401: #endif
402: #ifdef VMS
403: fflush_binary();
404: #endif
405: }
406:
407: /* output file must be binary mode for nec_dump */
408: void nec_draft_dump()
409: {
410: unsigned int x;
411: unsigned int plane, offset;
412: int j;
413: fputs("\033P\033l\005\r", gpoutfile); /* 10cpi, left margin 5 char */
414: for (j = (b_ysize / 8) - 1; j >= 0; j--) {
415: fputs("\033J\030", gpoutfile); /* 24/180" line feed */
416: for (plane = 0; plane < b_planes; plane++) {
417: offset = plane * b_psize;
418: if (b_planes > 1) {
419: /* select colour for plane */
420: fputs("\033r", gpoutfile);
421: (void) fputc((char) necpcolor[plane], gpoutfile);
422: }
423: /* select plotter graphics mode (square pixels) */
424: fputs("\r\033*", gpoutfile);
425: (void) fputc('\0', gpoutfile);
426: (void) fputc((char) (b_xsize % 256), gpoutfile);
427: (void) fputc((char) (b_xsize / 256), gpoutfile);
428: for (x = 0; x < b_xsize; x++) {
429: (void) fputc((char) (*((*b_p)[j + offset] + x)), gpoutfile);
430: }
431: }
432: }
433: fputs("\r\033l", gpoutfile);
434: (void) fputc('\0', gpoutfile); /* set left margin to 0 */
435: if (b_planes > 1) {
436: fputs("\033r", gpoutfile);
437: (void) fputc('\0', gpoutfile); /* set color to black */
438: }
439: #ifdef PC
440: fputs("Print using: COPY /B\n", gpoutfile);
441: #endif
442: }
443:
444: #endif /* NEC */
445:
446: #ifdef STARC
447: /* The following Star color driver uses generic bit mapped graphics
448: routines to build up a bit map in memory. */
449: /* Star Color changes made by William Wilson, wew@naucse.cse.nau.edu */
450: /* On PC, print using 'copy file /b lpt1:', do NOT use 'print' */
451: /* STARC_init changes gpoutfile to binary mode on PC's */
452:
453: void STARC_dump __PROTO((void));
454:
455: #define STARCXLAST (STARCXMAX - 1)
456: #define STARCYLAST (STARCYMAX - 1)
457:
458:
459: /* plane 0=black, 1=cyan(blue), 2=magenta(red), 3=yellow */
460: static unsigned int STARCcolor[] = { 1, 8, 4, 2, 10, 12, 6, 14 };
461: static unsigned int STARCpcolor[] = { 0, 2, 1, 4 };
462:
463: TERM_PUBLIC void STARCinit()
464: {
465: }
466:
467: TERM_PUBLIC void STARCgraphics()
468: {
469: b_charsize(FNT5X9);
470: b_makebitmap((unsigned int) (STARCXMAX * xsize),
471: (unsigned int) (STARCYMAX * ysize), 4);
472: }
473:
474:
475: TERM_PUBLIC void STARCtext()
476: {
477: STARC_dump();
478: b_freebitmap();
479: }
480:
481: TERM_PUBLIC void STARClinetype(linetype)
482: int linetype;
483: {
484: if (linetype >= 6)
485: linetype %= 6;
486: b_setvalue(STARCcolor[linetype + 2]);
487: }
488:
489:
490:
491: TERM_PUBLIC void STARCreset()
492: {
493: #ifdef VMS
494: fflush_binary();
495: #endif
496: }
497:
498:
499: /* output file must be binary mode for STARC_dump */
500: void STARC_dump()
501: {
502: unsigned int x;
503: unsigned int plane, offset;
504: int j;
505: for (j = (b_ysize / 8) - 1; j >= 0; j--) {
506: fputs("\033J\030", gpoutfile); /* line feed 8/72" = 8 dots */
507: for (plane = 0; plane < b_planes; plane++) {
508: offset = plane * b_psize;
509: if (b_planes > 1) {
510: /* select colour for plane */
511: fputs("\033r", gpoutfile);
512: (void) fputc((char) STARCpcolor[plane], gpoutfile);
513: }
514: /* select plotter graphics mode (square pixels) */
515: fputs("\r\033*\005", gpoutfile);
516: (void) fputc((char) (b_xsize % 256), gpoutfile);
517: (void) fputc((char) (b_xsize / 256), gpoutfile);
518: for (x = 0; x < b_xsize; x++) {
519: (void) fputc((char) (*((*b_p)[j + offset] + x)), gpoutfile);
520: }
521: }
522: }
523: if (b_planes > 1) {
524: fputs("\033r", gpoutfile);
525: (void) fputc('\0', gpoutfile); /* set color to black */
526: }
527: #ifdef PC
528: fputs("Print using: COPY /B\n", stderr);
529: #endif
530: }
531:
532: #endif /* STARC */
533:
534:
535: #ifdef EPS180
536:
537: void eps180_dump __PROTO((void));
538:
539: #define EPS180XLAST (EPS180XMAX - 1)
540: #define EPS180YLAST (EPS180YMAX - 1)
541:
542: TERM_PUBLIC void EPS180graphics()
543: {
544: b_charsize(FNT13X25);
545: b_makebitmap((unsigned int) (EPS180XMAX * xsize),
546: (unsigned int) (EPS180YMAX * ysize), 1);
547: }
548:
549:
550: TERM_PUBLIC void EPS180text()
551: {
552: eps180_dump();
553: b_freebitmap();
554: }
555:
556:
557:
558: /* output file must be binary mode for eps180_dump */
559: void eps180_dump()
560: {
561: register unsigned int x;
562: int j;
563:
564: /* reset, set line spacing to 24/180", and move left margin */
565: fputs("\033@\033+\060\033l\005", gpoutfile);
566: for (j = (b_ysize / 8) - 1; j >= 0;) {
567: /* select printer graphics mode '39' */
568: fputs("\r\n\033*'", gpoutfile);
569: (void) fputc((char) (b_xsize % 256), gpoutfile);
570: (void) fputc((char) (b_xsize / 256), gpoutfile);
571: for (x = 0; x < b_xsize; x++) {
572: (void) fputc((char) (*((*b_p)[j] + x)), gpoutfile);
573: (void) fputc((char) (*((*b_p)[j - 1] + x)), gpoutfile);
574: (void) fputc((char) (*((*b_p)[j - 2] + x)), gpoutfile);
575: }
576: j -= 3;
577: }
578: fputs("\r\n\033@\r\n", gpoutfile); /* reset printer */
579: #ifdef PC
580: fputs("Print using: COPY /B\n", stderr);
581: #endif
582: }
583:
584: #endif /* EPS180 */
585:
586: #ifdef EPS60
587:
588: void eps60_dump __PROTO((void));
589:
590: #define EPS60XLAST (EPS60XMAX - 1)
591: #define EPS60YLAST (EPS60YMAX - 1)
592:
593: TERM_PUBLIC void EPS60graphics()
594: {
595: b_charsize(FNT5X9);
596: b_makebitmap((unsigned int) (EPS60XMAX * xsize),
597: (unsigned int) (EPS60YMAX * ysize), 1);
598: }
599:
600:
601: TERM_PUBLIC void EPS60text()
602: {
603: eps60_dump();
604: b_freebitmap();
605: }
606:
607:
608:
609: /* output file must be binary mode for eps60_dump */
610: void eps60_dump()
611: {
612: register unsigned int x;
613: int j;
614: fprintf(gpoutfile, "\033%c\030", '3'); /* set line spacing 24/216" = 8 dots */
615: for (j = (b_ysize / 8) - 1; j >= 0; j--) {
616: /* select printer graphics mode 'K' */
617: fputs("\r\n\033K", gpoutfile);
618: (void) fputc((char) (b_xsize % 256), gpoutfile);
619: (void) fputc((char) (b_xsize / 256), gpoutfile);
620: for (x = 0; x < b_xsize; x++) {
621: (void) fputc((char) (*((*b_p)[j] + x)), gpoutfile);
622: }
623: }
624: fprintf(gpoutfile, "\033%c\044\r\n", '3'); /* set line spacing 36/216" = 1/6" */
625: #ifdef PC
626: fputs("Print using: COPY /B\n", stderr);
627: #endif
628: }
629:
630: #endif /* EPS60 */
631:
632: #ifdef TANDY60
633:
634: /* The only difference between TANDY60 and EPS60 is the inclusion
635: of codes to swap the Tandy printer into IBM mode and back
636: into Tandy mode. For a Tandy already in IBM mode, use EPS60. */
637:
638:
639: TERM_PUBLIC void TANDY60text()
640: {
641: #ifdef PC
642: fputs("Inserting Tandy/IBM mode conversion codes\n", stderr);
643: #endif
644: /* Switch to IBM mode, and leave 3 inches above the plot so as
645: to get rough vertical centring on the page. Perform the
646: centring by setting 1" line feeds and issuing 3 of them. */
647: fprintf(gpoutfile, "\033!\033%c%c\n\n\n", '3', 216);
648: eps60_dump();
649: b_freebitmap();
650: /* A form feed must be sent before switching back to Tandy mode,
651: or else the form setting will be messed up. */
652: fputs("\f\033!", gpoutfile);
653: }
654:
655:
656: #endif /* TANDY60 */
657:
658: #ifdef OKIDATA
659:
660: void okidata_dump __PROTO((void));
661:
662: TERM_PUBLIC void OKIDATAtext()
663: {
664: okidata_dump();
665: b_freebitmap();
666: }
667:
668: int bitrev_tbl[] =
669: {
670: 0x00, 0x80, 0x40, 0xc0, 0x20, 0xa0, 0x60, 0xe0,
671: 0x10, 0x90, 0x50, 0xd0, 0x30, 0xb0, 0x70, 0xf0,
672: 0x08, 0x88, 0x48, 0xc8, 0x28, 0xa8, 0x68, 0xe8,
673: 0x18, 0x98, 0x58, 0xd8, 0x38, 0xb8, 0x78, 0xf8,
674: 0x04, 0x84, 0x44, 0xc4, 0x24, 0xa4, 0x64, 0xe4,
675: 0x14, 0x94, 0x54, 0xd4, 0x34, 0xb4, 0x74, 0xf4,
676: 0x0c, 0x8c, 0x4c, 0xcc, 0x2c, 0xac, 0x6c, 0xec,
677: 0x1c, 0x9c, 0x5c, 0xdc, 0x3c, 0xbc, 0x7c, 0xfc,
678: 0x02, 0x82, 0x42, 0xc2, 0x22, 0xa2, 0x62, 0xe2,
679: 0x12, 0x92, 0x52, 0xd2, 0x32, 0xb2, 0x72, 0xf2,
680: 0x0a, 0x8a, 0x4a, 0xca, 0x2a, 0xaa, 0x6a, 0xea,
681: 0x1a, 0x9a, 0x5a, 0xda, 0x3a, 0xba, 0x7a, 0xfa,
682: 0x06, 0x86, 0x46, 0xc6, 0x26, 0xa6, 0x66, 0xe6,
683: 0x16, 0x96, 0x56, 0xd6, 0x36, 0xb6, 0x76, 0xf6,
684: 0x0e, 0x8e, 0x4e, 0xce, 0x2e, 0xae, 0x6e, 0xee,
685: 0x1e, 0x9e, 0x5e, 0xde, 0x3e, 0xbe, 0x7e, 0xfe,
686: 0x01, 0x81, 0x41, 0xc1, 0x21, 0xa1, 0x61, 0xe1,
687: 0x11, 0x91, 0x51, 0xd1, 0x31, 0xb1, 0x71, 0xf1,
688: 0x09, 0x89, 0x49, 0xc9, 0x29, 0xa9, 0x69, 0xe9,
689: 0x19, 0x99, 0x59, 0xd9, 0x39, 0xb9, 0x79, 0xf9,
690: 0x05, 0x85, 0x45, 0xc5, 0x25, 0xa5, 0x65, 0xe5,
691: 0x15, 0x95, 0x55, 0xd5, 0x35, 0xb5, 0x75, 0xf5,
692: 0x0d, 0x8d, 0x4d, 0xcd, 0x2d, 0xad, 0x6d, 0xed,
693: 0x1d, 0x9d, 0x5d, 0xdd, 0x3d, 0xbd, 0x7d, 0xfd,
694: 0x03, 0x83, 0x43, 0xc3, 0x23, 0xa3, 0x63, 0xe3,
695: 0x13, 0x93, 0x53, 0xd3, 0x33, 0xb3, 0x73, 0xf3,
696: 0x0b, 0x8b, 0x4b, 0xcb, 0x2b, 0xab, 0x6b, 0xeb,
697: 0x1b, 0x9b, 0x5b, 0xdb, 0x3b, 0xbb, 0x7b, 0xfb,
698: 0x07, 0x87, 0x47, 0xc7, 0x27, 0xa7, 0x67, 0xe7,
699: 0x17, 0x97, 0x57, 0xd7, 0x37, 0xb7, 0x77, 0xf7,
700: 0x0f, 0x8f, 0x4f, 0xcf, 0x2f, 0xaf, 0x6f, 0xef,
701: 0x1f, 0x9f, 0x5f, 0xdf, 0x3f, 0xbf, 0x7f, 0xff
702: };
703:
704: /* output file must be binary mode for okidata_dump */
705: void okidata_dump()
706: {
707: register unsigned int x;
708: int j;
709: char cur_char;
710: int prev_char;
711:
712: prev_char = 0;
713: fprintf(gpoutfile, "\033%c%c\020\033*eP:\003", '%', '9'); /* set line spacing 16/144" = 8 dots :Turned on single density graphics mode */
714: for (j = (b_ysize / 8) - 1; j >= 0; j--) {
715: fputs("\003\016", gpoutfile);
716: /* (void) fputc((char)(b_xsize%256),gpoutfile); */
717: /* (void) fputc((char)(b_xsize/256),gpoutfile); */
718: for (x = 0; x < b_xsize; x++) {
719: if ((cur_char = (char)
720: (bitrev_tbl[(int) (*((*b_p)[j] + x))])) == '\003') {
721: fputs("\003\003", gpoutfile);
722: } else {
723: (void) fputc((char) cur_char, gpoutfile);
724: }
725: }
726: }
727: fprintf(gpoutfile, "\003\002\033%c%c\030\r\n", '%', '9'); /* Turned off graphics mode: set line spacing 24/144" = 1/6" */
728: #ifdef PC
729: fputs("Print using: COPY /B\n", stderr);
730: #endif
731: }
732:
733: #endif /* OKIDATA */
734:
735: #endif /* TERM_BODY */
736:
737: #ifdef TERM_TABLE
738:
739: #ifdef EPS180
740: TERM_TABLE_START(epson180_driver)
741: "epson_180dpi", "Epson LQ-style 180-dot per inch (24 pin) printers",
742: EPS180XMAX, EPS180YMAX, EPSON180VCHAR, EPSON180HCHAR,
743: EPSON180VTIC, EPSON180HTIC, options_null, EPSONinit, EPSONreset,
744: EPS180text, null_scale, EPS180graphics, EPSONmove, EPSONvector,
745: EPSONlinetype, EPSONput_text, EPSON_text_angle,
746: null_justify_text, do_point, do_arrow, set_font_null, 0, TERM_BINARY
747: TERM_TABLE_END(epson180_driver)
748:
749: #undef LAST_TERM
750: #define LAST_TERM epson180_driver
751: #endif /* EPS180 */
752:
753: #ifdef EPS60
754: TERM_TABLE_START(epson60_driver)
755: "epson_60dpi", "Epson-style 60-dot per inch printers",
756: EPS60XMAX, EPS60YMAX, EPSONVCHAR, EPSONHCHAR,
757: EPSONVTIC, EPSONHTIC, options_null, EPSONinit, EPSONreset,
758: EPS60text, null_scale, EPS60graphics, EPSONmove, EPSONvector,
759: EPSONlinetype, EPSONput_text, EPSON_text_angle,
760: null_justify_text, do_point, do_arrow, set_font_null, 0, TERM_BINARY
761: TERM_TABLE_END(epson60_driver)
762:
763: #undef LAST_TERM
764: #define LAST_TERM epson60_driver
765: #endif /* EPS60 */
766:
767: #ifdef EPSONP
768: TERM_TABLE_START(epsonlx_driver)
769: "epson_lx800", "Epson LX-800, Star NL-10, NX-1000, PROPRINTER ...",
770: EPSONXMAX, EPSONYMAX, EPSONVCHAR, EPSONHCHAR,
771: EPSONVTIC, EPSONHTIC, options_null, EPSONinit, EPSONreset,
772: EPSONtext, null_scale, EPSONgraphics, EPSONmove, EPSONvector,
773: EPSONlinetype, EPSONput_text, EPSON_text_angle,
774: null_justify_text, line_and_point, do_arrow, set_font_null, 0, TERM_BINARY
775: TERM_TABLE_END(epsonlx_driver)
776:
777: #undef LAST_TERM
778: #define LAST_TERM epsonlx_driver
779: #endif /* EPSONP */
780:
781: #ifdef NEC
782: TERM_TABLE_START(nec_driver)
783: "nec_cp6", "NEC printer CP6, Epson LQ-800 [monocrome color draft]",
784: NECXMAX, NECYMAX, NECVCHAR, NECHCHAR,
785: NECVTIC, NECHTIC, NECoptions, NECinit, NECreset,
786: NECtext, null_scale, NECgraphics, NECmove, NECvector,
787: NEClinetype, NECput_text, NEC_text_angle,
788: null_justify_text, line_and_point, do_arrow, set_font_null, 0, TERM_BINARY
789: TERM_TABLE_END(nec_driver)
790:
791: #undef LAST_TERM
792: #define LAST_TERM nec_driver
793: #endif /* NEC */
794:
795: #ifdef OKIDATA
796: TERM_TABLE_START(okidata_driver)
797: "okidata", "OKIDATA 320/321 Standard",
798: EPS60XMAX, EPS60YMAX, EPSONVCHAR, EPSONHCHAR,
799: EPSONVTIC, EPSONHTIC, options_null, EPSONinit, EPSONreset,
800: OKIDATAtext, null_scale, EPS60graphics, EPSONmove, EPSONvector,
801: EPSONlinetype, EPSONput_text, EPSON_text_angle,
802: null_justify_text, do_point, do_arrow, set_font_null, 0, TERM_BINARY
803: TERM_TABLE_END(okidata_driver)
804:
805: #undef LAST_TERM
806: #define LAST_TERM okidata_driver
807: #endif /* OKIDATA */
808:
809: #ifdef STARC
810: TERM_TABLE_START(starc_driver)
811: "starc", "Star Color Printer",
812: STARCXMAX, STARCYMAX, STARCVCHAR, STARCHCHAR,
813: STARCVTIC, STARCHTIC, options_null, STARCinit, STARCreset,
814: STARCtext, null_scale, STARCgraphics, STARCmove, STARCvector,
815: STARClinetype, STARCput_text, STARC_text_angle,
816: null_justify_text, line_and_point, do_arrow, set_font_null, 0, TERM_BINARY
817: TERM_TABLE_END(starc_driver)
818:
819: #undef LAST_TERM
820: #define LAST_TERM starc_driver
821: #endif /* STARC */
822:
823: #ifdef TANDY60
824: TERM_TABLE_START(tandy60_driver)
825: "tandy_60dpi", "Tandy DMP-130 series 60-dot per inch graphics",
826: EPS60XMAX, EPS60YMAX, EPSONVCHAR, EPSONHCHAR,
827: EPSONVTIC, EPSONHTIC, options_null, EPSONinit, EPSONreset,
828: TANDY60text, null_scale, EPS60graphics, EPSONmove, EPSONvector,
829: EPSONlinetype, EPSONput_text, EPSON_text_angle,
830: null_justify_text, do_point, do_arrow, set_font_null, 0, TERM_BINARY
831: TERM_TABLE_END(tandy60_driver)
832:
833: #undef LAST_TERM
834: #define LAST_TERM tandy60_driver
835: #endif /* TANDY60 */
836:
837: #endif /* TERM_TABLE */
838: #endif /* TERM_PROTO_ONLY */
839:
840: #ifdef TERM_HELP
841: START_HELP(epson_180dpi)
842: "1 epson-180dpi",
843: "?commands set terminal epson-180dpi",
844: "?set terminal epson-180dpi",
845: "?set term epson-180dpi",
846: "?terminal epson-180dpi",
847: "?term epson-180dpi",
848: "?epson-180dpi",
849: "?commands set terminal epson-60dpi",
850: "?set terminal epson-60dpi",
851: "?set term epson-60dpi",
852: "?terminal epson-60dpi",
853: "?term epson-60dpi",
854: "?epson-60dpi",
855: "?commands set terminal epson-lx800",
856: "?set terminal epson-lx800",
857: "?set term epson-lx800",
858: "?terminal epson-lx800",
859: "?term epson-lx800",
860: "?epson-lx800",
861: "?commands set terminal nec-cp6",
862: "?set terminal nec-cp6",
863: "?set term nec-cp6",
864: "?terminal nec-cp6",
865: "?term nec-cp6",
866: "?nec-cp6",
867: "?commands set terminal okidata",
868: "?set terminal okidata",
869: "?set term okidata",
870: "?terminal okidata",
871: "?term okidata",
872: "?okidata",
873: "?commands set terminal starc",
874: "?set terminal starc",
875: "?set term starc",
876: "?terminal starc",
877: "?term starc",
878: "?starc",
879: "?commands set terminal tandy-60dpi",
880: "?set terminal tandy-60dpi",
881: "?set term tandy-60dpi",
882: "?terminal tandy-60dpi",
883: "?term tandy-60dpi",
884: "?tandy-60dpi",
885: " This driver supports a family of Epson printers and derivatives.",
886: "",
887: " `epson-180dpi` and `epson-60dpi` are drivers for Epson LQ-style 24-pin",
888: " printers with resolutions of 180 and 60 dots per inch, respectively.",
889: "",
890: " `epson-lx800` is a generic 9-pin driver appropriate for printers like the",
891: " Epson LX-800, the Star NL-10 and NX-1000, the PROPRINTER, and so forth.",
892: "",
893: " `nec-cp6` is generix 24-pin driver that can be used for printers like the",
894: " NEC CP6 and the Epson LQ-800.",
895: "",
896: " The `okidata` driver supports the 9-pin OKIDATA 320/321 Standard printers.",
897: "",
898: " The `starc` driver is for the Star Color Printer.",
899: "",
900: " The `tandy-60dpi` driver is for the Tandy DMP-130 series of 9-pin, 60-dpi",
901: " printers.",
902: "",
903: " Only `nec-cp6` has any options.",
904: "",
905: " Syntax:",
906: " set terminal nec-cp6 {monochrome | colour | draft}",
907: "",
908: " which defaults to monochrome.",
909: "",
910: " With each of these drivers, a binary copy is required on a PC to print. Do",
911: " not use `print`---use instead `copy file /b lpt1:`."
912: END_HELP(epson_180dpi)
913: #endif /* TERM_HELP */
FreeBSD-CVSweb <freebsd-cvsweb@FreeBSD.org>
![[BACK]](/icons/cvsweb/back.gif){kind=icon}
Return to epson.trm CVS log ![[TXT]](/icons/cvsweb/text.gif){kind=icon}
![[DIR]](/icons/cvsweb/dir.gif){kind=icon}
Up to [local] / OpenXM_contrib / gnuplot / term