Return to table.trm CVS log

Up to [local] / OpenXM_contrib / gnuplot / term

Annotation of OpenXM_contrib/gnuplot/term/table.trm, Revision 1.1.1.2

1.1       maekawa     1: /*
1.1.1.2 ! maekawa     2:  * $Id: table.trm,v 1.7 1998/11/25 21:08:17 lhecking Exp $
1.1       maekawa     3:  *
                      4:  */
                      5:
                      6: /* GNUPLOT - table.trm */
                      7:
                      8: /*[
                      9:  * Copyright 1986 - 1993, 1998   Thomas Williams, Colin Kelley
                     10:  *
                     11:  * Permission to use, copy, and distribute this software and its
                     12:  * documentation for any purpose with or without fee is hereby granted,
                     13:  * provided that the above copyright notice appear in all copies and
                     14:  * that both that copyright notice and this permission notice appear
                     15:  * in supporting documentation.
                     16:  *
                     17:  * Permission to modify the software is granted, but not the right to
                     18:  * distribute the complete modified source code.  Modifications are to
                     19:  * be distributed as patches to the released version.  Permission to
                     20:  * distribute binaries produced by compiling modified sources is granted,
                     21:  * provided you
                     22:  *   1. distribute the corresponding source modifications from the
                     23:  *    released version in the form of a patch file along with the binaries,
                     24:  *   2. add special version identification to distinguish your version
                     25:  *    in addition to the base release version number,
                     26:  *   3. provide your name and address as the primary contact for the
                     27:  *    support of your modified version, and
                     28:  *   4. retain our contact information in regard to use of the base
                     29:  *    software.
                     30:  * Permission to distribute the released version of the source code along
                     31:  * with corresponding source modifications in the form of a patch file is
                     32:  * granted with same provisions 2 through 4 for binary distributions.
                     33:  *
                     34:  * This software is provided "as is" without express or implied warranty
                     35:  * to the extent permitted by applicable law.
                     36: ]*/
                     37:
                     38: /*
                     39:  * The terminal 'table' is built into the source code; it is not
                     40:  * available separately.  This file is needed only for building
                     41:  * the documentation for gnuplot 3.6 (or higher) using the new
                     42:  * including mechanismn.
                     43:  */
                     44:
                     45: #ifdef TERM_REGISTER
                     46: register_term(table)
                     47: #endif
                     48:
                     49: #ifdef TERM_HELP
                     50: START_HELP(table)
                     51: "1 table",
                     52: "?commands set terminal table",
                     53: "?set terminal table",
                     54: "?set term table",
                     55: "?terminal table",
                     56: "?term table",
                     57: "?table",
                     58: " Instead of producing a graph, the `table` terminal prints out the points on",
                     59: " which a graph would be based, i.e., the results of processing the `plot` or",
                     60: " `splot` command, in a multicolumn ASCII table of X Y {Z} R values.  The",
                     61: " character R takes on one of three values: \"i\" if the point is in the active",
                     62: " range, \"o\" if it is out-of-range, or \"u\" if it is undefined.  The data",
                     63: " format is determined by the format of the axis labels (see `set format`).",
                     64: "",
                     65: " For those times when you want the numbers, you can display them on the",
                     66: " screen or save them to a file.  This can be useful if you want to generate",
                     67: " contours and then save them for further use, perhaps for plotting with",
                     68: " `plot`;  see `set contour` for an example.  The same method can be used to",
                     69: " save interpolated data (see `set samples` and `set dgrid3d`)."
                     70: END_HELP(table)
                     71: #endif